Home » Posts filed under 2014
J. Byun,
H. A. Patel,
C. T. Yavuz*
J. Nanopart. Res., 16:2787 (2014). [
DOI]
Magnetic nanoparticles are promising in applications where magnetic separation is intended, although material losses via leaching mechanisms are often inevitable. Magnetic separations with widely available permanent magnets can effectively trap particles, leading to a complete removal of used or waste particles. In this report, we first demonstrate the synthesis of the thinnest (112.7 ± 16.4 nm) and most magnetic (71.96 emu g−1) barium hexaferrite (BaFe12O19, BHF—fridge magnet) via an organic solvent-free electrospinning procedure. When the fibers are then packed into a column, they clearly remove 12 nm magnetite (Fe3O4) nanoparticles quantitatively. The same BHF cartridge also removes more than 99.9 % As-treated magnetite nanoparticles at capacities up to 70 times of its weight. As a result, one liter of 150 μg L−1 As-contaminated water can be purified rapidly at a material cost of less than 2 US cents.
[Continue reading...]
H. A. Patel,
D. Ko,
C. T. Yavuz*
Chem. Mater., 26 (23), 6729–6733 (2014). [
DOI]
The pursuit of synthetic routes for design and preparation of nanoporous polymeric networks with inherent permanent microporosity and functionality through bottom-up methodologies remains a driving force in developing CO2-philic materials. We report nanoporous, processable, benzoxazole-linked covalent organic polymers (Box-COPs) that show exceptional thermal stability up to 576 °C. Box-COPs can be formed into films thanks to the silylation that is used to guide polymeric network formation. Surface areas of up to 606 m2 g–1 and narrow pore sizes of 4.36 Å were observed with a CO2 uptake capacity of 139.6 mg g–1 at 273 K and 1 bar. Box-COPs were stable in boiling water for a week without deteriorating CO2 capture capacity.
[Continue reading...]
A. A. Raja,
C. T. Yavuz*
RSC Adv., 4 (104), 59779 - 59784 (2014). [
DOI] [pdf]
Order in purely organic network polymers is hard to achieve, as reversible, dynamic covalent bond formation is required. Strategies have focused on thermodynamically controlled transformations, as kinetics would not seemingly favour reversibility. Herein, we report formation of crystalline network polymers under kinetically favoured conditions by using quaternary ammonium salt linked networks. Charged bulky bridges align, even under fast reaction times (20 minutes) if the rotational freedom is granted. Adding vicinal methyl substituents blocks the ordering, hence forming amorphous networks. Raman experiments and SEM images reveal stacking of 2D layers.
[Continue reading...]
M. U. Alvi,
S. Zulfiqar,
C. T. Yavuz, H.S. Kweon, M. I. Sarwar*
Mater. Chem. Phys., 147, 636-643, (2014). [
DOI]

Aromatic polyamide/organoclay nanocomposites were synthesized using the solution blending technique. Treatment of montmorillonite clay with p-phenylenediamine produced reactive organophilic clay for good compatibility with the matrix. Polyamide chains were prepared by condensing a mixture of 1,4-phenylenediamine and 4-4′-oxydianiline with isophthaloyl chloride under anhydrous conditions. These chains were end capped with carbonyl chloride using 1% extra acid chloride near the end of reaction to develop the interactions with organoclay. The dispersion and structure–property relationship were monitored using FTIR, XRD, FE-SEM, TEM, DSC and tensile testing of the thin films. The structural investigations confirmed the formation of delaminated and disordered intercalated morphology with nanoclay loadings. This morphology of the nanocomposites resulted in their enhanced mechanical properties. The tensile behavior and glass transition temperature significantly augmented with increasing organoclay content showing a greater interaction between the two disparate phases.
[Continue reading...]
S. Zulfiqar, M. I. Sarwar*,
C. T. Yavuz*
RSC Adv., 4, 52263–52269, (2014). [
DOI]

Amide based porous organic polymers were synthesized by the reaction of 1,3,5-benzenetricarbonyl trichloride with 2,4,6-triamino-1,3,5-triazine using two different solvents. Polyamide chains were derived from tri-functional monomers and their relative properties were compared in both media. These polymers were subjected to various analyses including FTIR, XRD, TGA, BET surface area and pore size analysis, FESEM and CO2 adsorption measurements. Thermal and chemical stability was achieved through strong amide building blocks in the polymer structure. The basic ring nitrogen and amide groups in the polyamide networks had the affinity to capture CO2. The maximum CO2 uptake of 2.99 cm3 g−1 (0.134 mmol g−1) at 273 K and 1 bar was obtained with the polyamide synthesized in DMAc–NMP (PA-1), revealing better efficiency than the polyamide prepared using 1,4-dioxane (PA-2) due to higher porosity and improved surface area. These thermally stable polyamides are anticipated to be good sorbents for CO2 capture in hostile environments.
[Continue reading...]
M. Zahra,
S. Zulfiqar,
C. T. Yavuz, H.S. Kweon, M. I. Sarwar*
Compos. Sci. Technol., 100, 44–52, (2014). [
DOI]

Conductive nanocomposites were synthesized from surface modified clay and polypyrrole grafted triblock copolymer, polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene (SEBS-g-PPy). The grafting of PPy was carried out on SEBS using FeCl3 as an oxidant and the formation of subsequent materials was monitored by IR, 1H NMR spectroscopy and Gel permeation chromatography (GPC). Surface treatment of the clay was carried out by ion exchange method using the cationic salt of 2,2-bis[4-(4-aminophenoxy)phenyl]propane for better adhesion with the polymer matrix. Thin composite films containing 1–8-wt.% organoclay were investigated by FTIR, XRD, TEM, tensile testing, TGA, DSC and electrical conductivity measurements. The molar mass as determined by GPC was around 37,000. XRD pattern and TEM images described good dispersion of clay platelets in the nanocomposites. Tensile testing revealed improvement in mechanical properties up to 3-wt.% of organoclay. The bulk electrical conductivity was increased up to 7-wt.% with increase in resonance of delocalized electrons of stretched PPy chains due to hydrogen bonding with organoclay in the nanocomposites. Thermal decomposition temperatures of the nanocomposites were in the range 435–448 °C. The decomposition of the nanocomposites was observed at higher temperatures relative to the pure polymer matrix with increasing clay loading. The weight retained after 900 °C was approximately equal to the amount of organoclay added in the composites. These composite materials exhibited improvement in glass transition temperature as compared to SEBS-g-PPy.
[Continue reading...]
H. A. Patel, M. S. Yavuz,
C. T. Yavuz*
RSC Adv., 4 (46), 24320 - 24323, (2014). [
DOI] [pdf] [WOS]
Disulfide-linked covalent organic polymers (COPs) were prepared through catalyst-free oxidative coupling polymerization. Owing to the excellent swelling behavior, low cost, and efficient synthesis, these materials can be promising materials for removal of organics in concentrated streams. COPs show 1,4-dioxane uptake up to 1.8 g g
−1.
[Continue reading...]
J. Byun, S. H. Je,
H. A. Patel, A. Coskun,*
C. T. Yavuz*
J. Mater. Chem. A, 2, 12507-12512, 2014. [
DOI] [pdf] [WoS]
The CO
2 uptake capacity and CO
2/N
2 selectivity of Tröger’s base–bridged nanoporous covalent organic polymers (TB-COPs) were investigated. TB-COPs were synthesized by reacting amine terminals of tetrahedral monomers - namely, tetraanilyladamantane and tetraanilylmethane - with dimethoxymethane in a one–pot reaction under relatively mild conditions. Interestingly, these two tetrahedral monomers formed nanoporous polymers with substantially different surface areas. While the trögerization of tetraanilyladamantane monomer (TB-COP-1) exhibit high surface area of 1340 m2 g-1, that of tetraanilylmethane monomer (TB-COP-2) is found to be only 0.094 m2 g-1. This unusual phenomenon can be explained by the proximity of amino moieties to each other within the monomeric unit. Shorter distance between the amino groups enables intramolecular cyclization along with the intermolecular one, thus resulting in much lower porosity. TB-COP-1 exhibits significant CO2 uptakes up to 5.19 and 3.16 mmol g-1 at 273 and 298K under ambient pressure, and CO
2/N
2 selectivities of 79.2 and 68.9 at 273 and 298K at 1 bar for the gas mixture of CO
2:N
2 in the ratio of 0.15:0.85. It is noteworthy that TB-COP-1 showed remarkable selectivity retention with rising temperature from 273 to 298 K.
[Continue reading...]
H. A. Patel, S. H. Je, J. Park, Y. Jung, A. Coskun*,
C. T. Yavuz*
Chem. Eur. J., 20, 772-780, (2014). [
DOI] [pdf] [WOS]
A family of azo-bridged covalent organic polymers (azo-COPs) was synthesized through a catalyst-free direct coupling of aromatic nitro and amine compounds under basic conditions. The azo-COPs formed 3D nanoporous networks and exhibited surface areas up to 729.6 m2 g−1, with a CO2-uptake capacity as high as 2.55 mmol g−1 at 273 K and 1 bar. Azo-COPs showed remarkable CO2/N2 selectivities (95.6–165.2) at 298 K and 1 bar. Unlike any other porous material, CO2/N2 selectivities of azo-COPs increase with rising temperature. It was found that azo-COPs show less than expected affinity towards N2 gas, thus making the framework “N2-phobic”, in relative terms. Our theoretical simulations indicate that the origin of this unusual behavior is associated with the larger entropic loss of N2 gas molecules upon their interaction with azo-groups. The effect of fused aromatic rings on the CO2/N2 selectivity in azo-COPs is also demonstrated. Increasing the π-surface area resulted in an increase in the CO2-philic nature of the framework, thus allowing us to reach a CO2/N2 selectivity value of 307.7 at 323 K and 1 bar, which is the highest value reported to date. Hence, it is possible to combine the concepts of “CO2-philicity” and “N2-phobicity” for efficient CO2 capture and separation. Isosteric heats of CO2 adsorption for azo-COPs range from 24.8–32.1 kJ mol−1 at ambient pressure. Azo-COPs are stable up to 350 °C in air and boiling water for a week. A promising cis/trans isomerization of azo-COPs for switchable porosity is also demonstrated, making way for a gated CO2 uptake.
[Continue reading...]