Redox and Nonredox CO2 Utilization: Dry Reforming of Methane and Catalytic Cyclic Carbonate Formation

S. Subramanian, Y. Song, D. Kim, C. T. Yavuz*
ACS Energy Lett., 5, 5, 1689–1700 (2020). Invited Review
DOI: 10.1021/acsenergylett.0c00406

CO2 emissions are too large to tackle with a single process, but a combination of avoidance with chemical utilization may be able to slow global warming. In this Focus Review, we identify two large-scale CO2 conversion processes based on their viability and opposite energy requirements. In the high-energy, stationary path, CO2 reforming of methane could provide gigatons of CO2 utilization through synthesis gas. The main problem is the lack of a durable, effective, low-cost dry reforming catalyst. The exothermic cyclic carbonate formation from CO2 and organic epoxides offers a low-energy, mobile, nonredox route. The catalysts, however, must be metal-free and robust, have a high surface area, and be low-cost while being easily scalable. These two processes could potentially address at least a quarter of all current CO2 emissions.

[Continue reading...]

Triazatruxene-Based Ordered Porous Polymer: High Capacity CO2, CH4, and H2 Capture, Heterogeneous Suzuki–Miyaura Catalytic Coupling, and Thermoelectric Properties

A. E. Sadak*, E. Karakuş*, Y. Chumakov, N. A. Dogan, C. T. Yavuz 

ACS Appl. Energy Mater., 3, 5, 4983–4994 (2020). 

DOI: 10.1021/acsaem.0c00539

A hypercrosslinked ultramicroporous and ordered organic polymer network was synthesized from a planar trimer indole building block called triazatruxene (TAT) through anhydrous FeCl3 catalyzed Friedel–Crafts alkylation using methylal as a crosslinker. The polymer network is stable in a variety of chemicals and thermally durable. The hypercrosslinked network TATHCP shows a high BET (Brunauer–Emmet–Teller) specific surface area of 997 m2 g–1 with CO2 uptake capacity of 12.55 wt % at 273 K, 1.1 bar. Gas selectivities of 38.4 for CO2/N2, 7.8 for CO2/CH4, 40.6 for CO2/O2, and 32.1 for CO2/CO were achieved through IAST calculation. The PXRD analysis has revealed that TATHCP has a fully eclipsed structure in full agreement with Pawley refinement. The ordered 2D layers provide anisotropy that could be used in catalysis and thermoelectric measurements. After loading with Pd(II), TATHCP-Pd showed high catalytic activity in Suzuki–Miyaura cross coupling reaction with a wide range of reagents and excellent reaction yields of 90–98% with good recyclability. The structure of TATHCP-Pd was found to have two independent molecules of Pd(OAc)2 in the asymmetric unit cell which are arranged between two TATHCP layers. Thermoelectric properties of TATHCP showed a high Seebeck coefficient and ZT, a first and promising example in HCPs with applications in all-organic thermal energy recovery devices.

[Continue reading...]

Dry reforming of methane by stable Ni–Mo nanocatalysts on single-crystalline MgO

Y. Song, E. Ozdemir, S. Ramesh, A. Adishev, S. Subramanian, A. Harale, M. Albuali, B. A. Fadhel, A. Jamal, D. Moon, S. H. Choi, C. T. Yavuz*
Science, 367, 6479, 777-781 (2020).
DOI: 10.1126/science.aav2412

Large-scale carbon fixation requires high-volume chemicals production from carbon dioxide. Dry reforming of methane could provide an economically feasible route if coke- and sintering-resistant catalysts were developed. Here, we report a molybdenum-doped nickel nanocatalyst that is stabilized at the edges of a single-crystalline magnesium oxide (MgO) support and show quantitative production of synthesis gas from dry reforming of methane. The catalyst runs more than 850 hours of continuous operation under 60 liters per unit mass of catalyst per hour reactive gas flow with no detectable coking. Synchrotron studies also show no sintering and reveal that during activation, 2.9 nanometers as synthesized crystallites move to combine into stable 17-nanometer grains at the edges of MgO crystals above the Tammann temperature. Our findings enable an industrially and economically viable path for carbon reclamation, and the “Nanocatalysts On Single Crystal Edges” technique could lead to stable catalyst designs for many challenging reactions.

Perspective: Liyu Chen, Qiang Xu*, "Fewer defects, better catalysis?", p. 737
Research summary by Phil Szuromi, "Overcoming surface defects", p. 752-753
Highlighted in Chemistry World, C&EN, Nature Asia
Korean press release, English press release

Media Coverage:
Science Daily
Nanowerk
UPI
Phys.org
The Engineer
Wikipedia: 2020 in Science

Korean Media:
서울경제
해럴드경제
충청일보
교수신문
충남일보
베리타스알파
글로벌이코노믹
이뉴스투데이
뉴스핌
뉴스1
전자신문
국제뉴스
아시아경제
헬로디디
인더스트리뉴스
대전시티저널
에너지경제
아시아뉴스통신

[Continue reading...]

High-capacity methane storage in flexible alkane-linked porous aromatic network polymers

V. Rozyyev, D. Thirion, R. Ullah, J. Lee, M. Jung, H. Oh, M. Atilhan*, C. T. Yavuz*
Nat. Energy, 4, 604-611, (2019).
DOI: 10.1038/s41560-019-0427-x
Readcube link to read for free

Adsorbed natural gas (ANG) technology is a viable alternative to conventional liquefied or compressed natural-gas storage. Many different porous materials have been considered for adsorptive, reversible methane storage, but fall short of the US Department of Energy targets (0.5 g g−1, 263 l l−1). Here we prepare a flexible porous polymer, made from benzene and 1,2-dichloroethane in kilogram batches, that has a high methane working capacity of 0.625 g g−1 and 294 l l−1 when cycled between 5 and 100 bar pressure. We suggest that the flexibility provides rapid desorption and thermal management, while the hydrophobicity and the nature of the covalently bonded framework allow the material to tolerate harsh conditions. The polymer also shows an adsorbate memory effect, where a less adsorptive gas (N2) follows the isotherm profile of a high-capacity adsorbate (CO2), which is attributed to the thermal expansion caused by the adsorption enthalpy. The high methane capacity and memory effect make flexible porous polymers promising candidates for ANG technology.

[Continue reading...]